Exhaust System/Revmaster


joseph.m.tygart.alion@...
 

ALCON - This sure sounds like something I need for my hot running turbo
Revmaster! Where can you have this ceramic coating done? Muffler shops,
dealerships???

Speaking of warm Revmasters: I've almost got 762CP back in the air pending
resolution of engine idle problems, i.e. the engine idles perfectly @ 750
RPM, set by idle arm & control linkage. Upon reinstalling the engine
cowling and allowing the engine to warm up for a few minutes the RPM will
automatically increase to an average of 1450 RPM and remain until shutdown
and cooling. Makes for a real hot final! Sure would like to make it to the
Spring Fling. Is anyone familiar with this scenario? Comments &
suggestions please. Thanks, Joe Tygart Turbo-Q N762CP VA.

-----Original Message-----
From: Q-LIST@... [mailto:Q-LIST@...] On Behalf Of
rondefly@...
Sent: Tuesday, May 03, 2005 8:49 AM
To: Q-LIST@...
Subject: RE: [Q-LIST] Exhaust System.



Is this Ceramic coat a dipping process or did you just spray the exterior?

Ron & Carolyn Triano Q-200 N4710P

-----Original Message-----
From: Q-LIST@... [mailto:Q-LIST@...]On Behalf Of
Greg & Debbie Merrill
Sent: Tuesday, May 03, 2005 5:01 AM
To: Q-LIST@...
Subject: RE: [Q-LIST] Exhaust System.

Ditto!

-----Original Message-----
From: Q-LIST@... [mailto:Q-LIST@...]On Behalf Of
Jerry Marstall
Sent: May 2, 2005 8:00 PM
To: Q-LIST@...
Subject: Re: [Q-LIST] Exhaust System.


I had it done for the 4 into 1 on my Revmaster. Not only did it help
with heat reduction in the cowling, you don't have rusty pipes.
Jerry

Mike Dwyer wrote:

Hey Qers.
I had written about putting together a stainless exhaust system and ...
you were right, it is next to impossible to bend that stuff. It appears
only the mandrel bend machines can touch it.

Now I'm thinking about using steel to make a 4 pipe system. Each pipe
will exit at the bottom near the oil sump. I checked out this place
that ceramic coats the pipes, $20 per foot. They say it keeps the heat
in the pipes better. Does anyone here believe that or is it a waste of
money?

Thanks,
Mike Q200



Quickie Builders Association WEB site
http://www.quickiebuilders.org <http://www.quickiebuilders.org>


Yahoo! Groups Links











Quickie Builders Association WEB site
http://www.quickiebuilders.org <http://www.quickiebuilders.org>


Yahoo! Groups Links









Quickie Builders Association WEB site
http://www.quickiebuilders.org <http://www.quickiebuilders.org>





_____

Yahoo! Groups Links
* To visit your group on the web, go to:
http://groups.yahoo.com/group/Q-LIST/
<http://groups.yahoo.com/group/Q-LIST/>

* To unsubscribe from this group, send an email to:
Q-LIST-unsubscribe@...
<mailto:Q-LIST-unsubscribe@...?subject=Unsubscribe>

* Your use of Yahoo! Groups is subject to the Yahoo! Terms of
Service <http://docs.yahoo.com/info/terms/
<http://docs.yahoo.com/info/terms/> > .






Quickie Builders Association WEB site
http://www.quickiebuilders.org <http://www.quickiebuilders.org>






_____

Yahoo! Groups Links

* To visit your group on the web, go to:
http://groups.yahoo.com/group/Q-LIST/
<http://groups.yahoo.com/group/Q-LIST/>


* To unsubscribe from this group, send an email to:
Q-LIST-unsubscribe@...
<mailto:Q-LIST-unsubscribe@...?subject=Unsubscribe>


* Your use of Yahoo! Groups is subject to the Yahoo! Terms of
<http://docs.yahoo.com/info/terms/> Service.

Join main@Q-List.groups.io to automatically receive all group messages.