Re: Q1 Fuselage comes up


David J. Gall
 

Vern,

 

I appreciate your enthusiasm but:

Carbon and titanium and prohibitions – oh, my! These planes are made from super-cheap insulation materials sourced from Home Depot and a second-hand generator motor swiped from the derelict RV parked out back…. (not really, but if you spend more than $10,000 on a Quickie you might be doing it wrong!)

 

The stiffeners are plenty strong (they are, after all, “stiffeners,” not “strengtheners”) with just one layer of BID on each side. By the time they’re installed using 2 BID tapes and all the other nearby added layers of BID from the canard installation, they’re truck-strong….

 

David J. Gall

 

From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of smeshno1@...
Sent: Tuesday, July 6, 2021 10:13 AM
To: main@Q-List.groups.io
Subject: Re: [Q-List] Q1 Fuselage comes up

 

 David.. Eugen is installing a modified B&S Vanguard V2 engine. Structurally I agree with the additional stiffening. My memory of the Onan Q1 I flew years ago was that all things considered the vibration was on par with or a bit less than my O-200 taildragger 150.  It had to be an early build Q1..since I flew it in 1982 from ORK field located in Arkansas. 

 

 Eugen.. the stiffeners could be made with carbon fiber, and doing so will increase the tension strength of the firewall for the engine mount bolts considerably. Just be sure to not have any direct contact with aluminum alloy to the stiffeners (galvanic corrosion). This is a location where we would specify titanium bolts in the bizjet world. No corrosion issues provided no cadmium plated items (tools, washers, cotter pins, ect.) are ever used on the fasteners. Use of Alodine 1200 is also forbidden on titanium. 

 

 I am especially curious to see your engine installation. Your doing great progress and at this pace you'll be test flying soon.  

 

Vern in Mannford (Oklahoma, not Germany)  

 


From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of David J. Gall <David@...>
Sent: Tuesday, July 6, 2021 11:48 AM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: Re: [Q-List] Q1 Fuselage comes up

 

Eugen,

 

Yes, you understand the plans correctly with regard to the BID. You really should have a PDF of the original plans for reference; the OCR version on the Quickheads site is very well done but sometimes the original layout of the information on the page can help with understanding. You can download from my non-curated repository: https://DavidJGall.com/Q/Quickie/Quickie%20Plans/

 

While you’re building, be sure to notice on page 4-7 the two pieces called “firewall brace” for which the templates are drawn on page 15-2. I cannot find anywhere in the original plans that callout the installation of these parts or their precise location; perhaps it was covered in a QPC but I’m not going searching for it right now. It’s relatively obscure that these are part of the firewall primary structure because the QAC plans left it for the Onan installation chapter (and then never documented it there). I suspect that people who are not installing the original Onan may overlook these pieces. The best reference I can find for these pieces is on page 15 of the Jinx Hawks/Brock McCaman “SuperQuickie Conversion Plans” for installation of a Rotax 503, wherein they refer to these as “existing lower stiffeners.” See the attached picture:

 

It appears to me that the placement of these “firewall brace” pieces was far enough apart to admit the original steel “pie pan” firewall extension that accommodated the aft part of the Onan engine between the braces, yet as near to the aircraft centerline as possible to leave foot room for rudder pedal movement clearance. These braces were, partly, to stiffen the firewall for the lower, center engine mount from the three-point Onan mounting scheme; the Jinx/Brock modifications put four ply BID pads outboard of these braces to support the new four-point mount for the Rotax. If you’re installing anything other than an Onan I would strongly recommend following the SuperQuickie Conversion Plans for firewall and airframe preparation. You can download them here: https://davidjgall.com/Q/Quickie/

 

Keep going with the great build progress!

 

David J. Gall

Join main@Q-List.groups.io to automatically receive all group messages.