Re: Axle Removal Problems


Bruce Crain
 

Maybe a thick wall 4130 steel would do the trick.  You might need to get a smaller inside “keeper bolt” with thick washers.  I did this to my Q when it was still a tail stagger.  The keeper bolt that goes through the center of the axle might have been 1/4” or maybe 5/16”.  It bares no load except to keep the axle centered.  I had to cut mine out years ago also when still a tail stagger.
Bruce Crain


On Dec 30, 2021, at 4:00 PM, Mike Steinsland <MIKESKUSTOMS@...> wrote:


Glad you got the assembly off
Now you can beat on it on the bench and not wreck the wheel mount.
The idea of banging on that still inside the wheel pant gave me the heebeegeebees 

Cheers

On Thu., Dec. 30, 2021, 4:23 p.m. Jay Scheevel, <jay@...> wrote:

Hi Corbin,

 

Merry Christmas and Happy New Year!. It occurs to me that the issue may have been that the axle was slightly bent, maybe from a hard landing or other torque, so cutting it off was probably a good strategy regardless. Glad you got it out (or soon will) and will get your airplane functional again in the new year. Send us pics of your updated panel.

 

Cheers,

Jay

 

From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of Corbin via groups.io
Sent: Thursday, December 30, 2021 1:07 PM
To: main@q-list.groups.io
Subject: Re: [Q-List] Axle Removal Problems

 

Christmas shenanigans got in the way until this morning and I was able to get it out….sort of.  Freezing/shrinking didn’t work, tapping from all sides and techniques didn’t work, working lubricant in didn’t work, in the end I cut it off as close to the wheel pant as I could and was able to shove the steel push rod into the wheel pant enough for the tire to fall down and out.

 

Now I just have to take part the wheel and remove the bearing (which is what it is stuck on) and steel push rod and throw them as far as I can into the woods; never to be seen again.

Corbin



On Dec 30, 2021, at 12:31 PM, Mike Steinsland <MIKESKUSTOMS@...> wrote:



Did you ever get that out or did Christmas get in the way?

 

On Fri., Dec. 24, 2021, 2:32 p.m. Mike Steinsland via groups.io, <MIKESKUSTOMS=GMAIL.COM@groups.io> wrote:

Definitely lubricate it as you get it going

Hopefully the lubricant works it's way into the wheel

You may have to tap it back and forth a lot.....a little at a time, like rocking a stuck car back and forth

 

On Thu., Dec. 23, 2021, 7:25 p.m. Bruce Crain, <jcrain2@...> wrote:

Maybe get someone to tap once on the outside and then tap the inside to see if that will loosen it.  You could use propane to super freeze the tube and see if it can make it shrink enough to move it.  Don’t smoke!
Bruce
> On Dec 23, 2021, at 12:12 PM, Corbin via groups.io <c_geiser=icloud.com@groups.io> wrote:
>
> [Edited Message Follows]
>
> Typos corrected:  I’ve always had a bit of a headache removing the axle when needing to remove the tire.  In one of the pics below, the darker steel rod is what I use to slide in and tap out the axle (which is the other pic).  The axle will easily pull out from the position in the pic.  However, the rod I use to tap out the axle is stuck and won’t move back out or further in.
>
> I have the plane raised so there is no weight on the tire.  I have tried tapping the axle back in to push back out the rod.  I’ve reached the point of, “nothing should ever be tapped that hard” so I’m stumped.
>
> The tire and wheel spin freely.  I’m tempted to cut the steel rod off as close to the wheel pant as I can just so I can get the tire/wheel out.
>
> Any ideas out there on a solution or something worth trying?
>
>
>
> Corbin
>
> --
> Corbin
> N121CG
>
>
>
>
>
> <image0.jpeg>
> <image1.jpeg>


____________________________________________________________
Choose to be safer online.
Opt-in to Cyber Safety with NortonLifeLock.
Plans starting as low as $6.95 per month.*
https://store.netzero.net/account/showService.do?serviceId=nz-nLifeLock&utm_source=mktg&utm_medium=taglines&utm_campaign=nzlifelk_launch&utm_content=tag695&promoCode=A34454





--

Corbin 
N121CG



Join main@Q-List.groups.io to automatically receive all group messages.