Date   

Cowl Exit Augmentation

Bruce Crain
 

I am finally finishing my cowl exit augmenter so I wanted to touch on a couple of things about it.
The fiberglass part in this picture lowers the exit below where the original hung. It not only opens it up at the aft end it also lowers it below the oil bladder which obstructs the outflow quite a bit.
The other picture with the orange baffling material is a big help also. All of this helps the TriQ family as the nose gear descends through the bottom of the cowling. The opening for the gear leg lets a lot of high pressure come into the cowl blocking the exit air. Having flown the original and this retro-fit I can tell you it lowers my cylinder head temps and especially my oil temps.
Just sayin’
Bruce Crain
Working for Spring Fling, Oshkosh, Field of Dreams and where ever Honey wants to go! Get em done and maintained and enjoyed!


Re: Oil leak - Cylinder Base

Jay Scheevel
 

Congrats on getting your leak controlled, Bruce!

 

Cheers,

Jay

 

From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of Bruce Crain
Sent: Thursday, March 26, 2020 4:59 PM
To: main@Q-List.groups.io
Subject: Re: [Q-List] Oil leak - Cylinder Base

 

After pulling the number 4  cylinder and putting o rings on the front two through bolts I tested it out today.  After the 1st flight the leak was worse!!  I pulled it back into the hanger and pulled the cowling. 

 

The leak was coming from the #4 cylinder!  Piffle!!  But I did notice it was coming from the rocker box cover.  I had reused the silicone gasket and knew that was probably the culprit!  So I pulled the rocker cover and could see a small chunk out of the gasket.  I located the chunk in the tin bucket underneath to catch the oil so I knew it wasn't in the crank case.  I put a  new silicone rocker cover gasket on it and flew it again for about  3 tenth of an hour.  When I looked under the fuz there was not any oil showing!!!!  After all these years I finally have a DRY BELLY!

 

Kevin Boddecker I am still working towards your Spring Fling and this is the biggest fix that needed to be done.  I am also working on a couple of other cosmetics things plus I will continue to up date on my sparrow strainer stall.  I am thinking I need to re-position the zig zag tape further back on the apex of the strainer to see if that works differently.  Will let you know when I get a chance to test that.

 

 Great day to fly!  Not much wind and 68 degrees!

 

What a great airplane!

Bruce Crain 

N96BJ  

 


Re: Oil leak - Cylinder Base

Bruce Crain
 

After pulling the number 4  cylinder and putting o rings on the front two through bolts I tested it out today.  After the 1st flight the leak was worse!!  I pulled it back into the hanger and pulled the cowling. 
 
The leak was coming from the #4 cylinder!  Piffle!!  But I did notice it was coming from the rocker box cover.  I had reused the silicone gasket and knew that was probably the culprit!  So I pulled the rocker cover and could see a small chunk out of the gasket.  I located the chunk in the tin bucket underneath to catch the oil so I knew it wasn't in the crank case.  I put a  new silicone rocker cover gasket on it and flew it again for about  3 tenth of an hour.  When I looked under the fuz there was not any oil showing!!!!  After all these years I finally have a DRY BELLY!
 
Kevin Boddecker I am still working towards your Spring Fling and this is the biggest fix that needed to be done.  I am also working on a couple of other cosmetics things plus I will continue to up date on my sparrow strainer stall.  I am thinking I need to re-position the zig zag tape further back on the apex of the strainer to see if that works differently.  Will let you know when I get a chance to test that.
 
 Great day to fly!  Not much wind and 68 degrees!
 
What a great airplane!
Bruce Crain 
N96BJ  
 


Re: Brakes

Jim Patillo
 

That would be my guess as well.
Jim

Sent from Outer Space


From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser@...>
Sent: Thursday, March 26, 2020 3:59:13 PM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: Re: [Q-List] Brakes
 
Thanks Jim!  No, I don't have the original plans. This started happening a few months ago and I only noticed that it was catching the tire when I would pull the plane backwards.  Going forward, it seemed fine but now it seems to be rubbing either direction so I assume Martin is right and I got the spacer washers back incorrectly.

Corbin 

On March 26, 2020 at 5:42 PM, Jim Patillo <Logistics_engineering@...> wrote:

Corbin,

This is the LaRue Mod on my plane. The entire Airheart assembly floats so the pucks stay centered on the disc. Yours appears to be stock. Meaning that the Airheart assembly is fixed. Do you have the original QAC plans for that set up? Those plans will show the required spacing.

Did this problem just happen?
Jim
N46JP - Q200





--

Corbin 
N33QR


Re: Brakes

Corbin
 

Thanks Jim!  No, I don't have the original plans. This started happening a few months ago and I only noticed that it was catching the tire when I would pull the plane backwards.  Going forward, it seemed fine but now it seems to be rubbing either direction so I assume Martin is right and I got the spacer washers back incorrectly.

Corbin 

On March 26, 2020 at 5:42 PM, Jim Patillo <Logistics_engineering@...> wrote:

Corbin,

This is the LaRue Mod on my plane. The entire Airheart assembly floats so the pucks stay centered on the disc. Yours appears to be stock. Meaning that the Airheart assembly is fixed. Do you have the original QAC plans for that set up? Those plans will show the required spacing.

Did this problem just happen?
Jim
N46JP - Q200





--

Corbin 
N33QR


Brakes

Jim Patillo
 

Corbin,

This is the LaRue Mod on my plane. The entire Airheart assembly floats so the pucks stay centered on the disc. Yours appears to be stock. Meaning that the Airheart assembly is fixed. Do you have the original QAC plans for that set up? Those plans will show the required spacing.

Did this problem just happen?
Jim
N46JP - Q200


Re: Brake (Anvil) Rubbing Tire

Corbin
 

Thanks Jim.  I have the Airheart brake assembly.

2019-08-15_14-04-54_843.jpg
Corbin Ge!ser

On March 26, 2020 at 4:24 PM, Jim Patillo <Logistics_engineering@...> wrote:

No worries. You can call anytime Corbin. I can’t remember if you have the LaRue brake mod? Can you verify?

Jim
N46JP - Q200

Sent from Outer Space

From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser@...>
Sent: Thursday, March 26, 2020 2:21:03 PM
To: main@q-list.groups.io <main@q-list.groups.io>
Subject: Re: [Q-List] Brake (Anvil) Rubbing Tire
 
Awesome.  Could I call you tomorrow?  Is there a best time?

Corbin

On Mar 26, 2020, at 4:15 PM, Jim Patillo <Logistics_engineering@...> wrote:

Hi Corbin, I may be able to walk you thru that adjustment. My #510-468-4891. Give me a call if you would like to discuss.

Jim
N46JP - Q200

Sent from Outer Space

From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser@...>
Sent: Thursday, March 26, 2020 11:56:49 AM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: Re: [Q-List] Brake (Anvil) Rubbing Tire
 
It is so dark up in the wheel well that I couldn't get a good one.  I will take my endoscope camera out there next time and get a photo/video.  

Corbin

On March 26, 2020 at 1:42 PM, Jim Patillo <Logistics_engineering@...> wrote:

You have a pix?
Jim
N46JP - Q200

Sent from Outer Space

From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser@...>
Sent: Thursday, March 26, 2020 11:38:36 AM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: [Q-List] Brake (Anvil) Rubbing Tire
 
Hey guys,

Some of you saw my photos of the dried brake fluid on my brake caliper and now I have another brake related issue I need your experience to help with.  First, I was able to get the caliper all cleaned up and everything looks good so I am going to keep an eye out for small leaks. 

Now my problem is that the anvil (inside part of the brake caliper) is rubbing up against the tire.  No matter how I try and line it up it still rubs the tire just enough to stop it from spinning freely.  I even thought maybe I have too much air in the tire causing it to bulge out too far.  I will double check that in coming days just in case.  I thought I might could get a grinder and grind down the anvil a 1/4 inch or so.....

Any other thoughts?  I am certain the anvil is correctly installed onto the caliper and the bolts have no issues lining up and going in.  

Corbin

--

Corbin 
N33QR




--

Corbin 
N33QR

--

Corbin 
N33QR




--

Corbin 
N33QR


Re: Brake (Anvil) Rubbing Tire

Martin Skiby
 

Don't get me wrong, it was very tight, but we were able to get it not to rub.

Good luck!


-----------------------------------------

From: "Corbin via Groups.Io"
To: main@q-list.groups.io
Cc:
Sent: Thursday March 26 2020 12:29:20PM
Subject: Re: [Q-List] Brake (Anvil) Rubbing Tire

Awesome....I will go back and look at some old photos that I took to make sure I place them just like they were.  I’m 100% sure I took photos the very first time I worked on the brakes.

Corbin

On Mar 26, 2020, at 2:12 PM, Martin Skiby <mskiby@...> wrote:

Corbin,
The washer placement on the mounting of the caliper was key to getting it to not hit when we put it together.  Make sure all of the washers are exactly where they were.  I believe there were washers used as spacers under the caliper mount.

That it about all the advice I have on that one without seeing it.

-----------------------------------------

From: "Corbin via Groups.Io"
To: main@Q-List.groups.io
Cc:
Sent: Thursday March 26 2020 11:56:49AM
Subject: Re: [Q-List] Brake (Anvil) Rubbing Tire

It is so dark up in the wheel well that I couldn't get a good one.  I will take my endoscope camera out there next time and get a photo/video.  

Corbin

On March 26, 2020 at 1:42 PM, Jim Patillo <Logistics_engineering@...> wrote:

You have a pix?
Jim
N46JP - Q200

Sent from Outer Space

From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser@...>
Sent: Thursday, March 26, 2020 11:38:36 AM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: [Q-List] Brake (Anvil) Rubbing Tire
 
Hey guys,

Some of you saw my photos of the dried brake fluid on my brake caliper and now I have another brake related issue I need your experience to help with.  First, I was able to get the caliper all cleaned up and everything looks good so I am going to keep an eye out for small leaks. 

Now my problem is that the anvil (inside part of the brake caliper) is rubbing up against the tire.  No matter how I try and line it up it still rubs the tire just enough to stop it from spinning freely.  I even thought maybe I have too much air in the tire causing it to bulge out too far.  I will double check that in coming days just in case.  I thought I might could get a grinder and grind down the anvil a 1/4 inch or so.....

Any other thoughts?  I am certain the anvil is correctly installed onto the caliper and the bolts have no issues lining up and going in.  

Corbin

--

Corbin 
N33QR




Re: Brake (Anvil) Rubbing Tire

Jim Patillo
 

No worries. You can call anytime Corbin. I can’t remember if you have the LaRue brake mod? Can you verify?

Jim
N46JP - Q200

Sent from Outer Space


From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser@...>
Sent: Thursday, March 26, 2020 2:21:03 PM
To: main@q-list.groups.io <main@q-list.groups.io>
Subject: Re: [Q-List] Brake (Anvil) Rubbing Tire
 
Awesome.  Could I call you tomorrow?  Is there a best time?

Corbin

On Mar 26, 2020, at 4:15 PM, Jim Patillo <Logistics_engineering@...> wrote:


Hi Corbin, I may be able to walk you thru that adjustment. My #510-468-4891. Give me a call if you would like to discuss.

Jim
N46JP - Q200

Sent from Outer Space

From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser@...>
Sent: Thursday, March 26, 2020 11:56:49 AM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: Re: [Q-List] Brake (Anvil) Rubbing Tire
 
It is so dark up in the wheel well that I couldn't get a good one.  I will take my endoscope camera out there next time and get a photo/video.  

Corbin

On March 26, 2020 at 1:42 PM, Jim Patillo <Logistics_engineering@...> wrote:

You have a pix?
Jim
N46JP - Q200

Sent from Outer Space

From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser@...>
Sent: Thursday, March 26, 2020 11:38:36 AM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: [Q-List] Brake (Anvil) Rubbing Tire
 
Hey guys,

Some of you saw my photos of the dried brake fluid on my brake caliper and now I have another brake related issue I need your experience to help with.  First, I was able to get the caliper all cleaned up and everything looks good so I am going to keep an eye out for small leaks. 

Now my problem is that the anvil (inside part of the brake caliper) is rubbing up against the tire.  No matter how I try and line it up it still rubs the tire just enough to stop it from spinning freely.  I even thought maybe I have too much air in the tire causing it to bulge out too far.  I will double check that in coming days just in case.  I thought I might could get a grinder and grind down the anvil a 1/4 inch or so.....

Any other thoughts?  I am certain the anvil is correctly installed onto the caliper and the bolts have no issues lining up and going in.  

Corbin

--

Corbin 
N33QR




--

Corbin 
N33QR

--

Corbin 
N33QR


Re: Brake (Anvil) Rubbing Tire

Corbin
 

Awesome.  Could I call you tomorrow?  Is there a best time?

Corbin

On Mar 26, 2020, at 4:15 PM, Jim Patillo <Logistics_engineering@...> wrote:


Hi Corbin, I may be able to walk you thru that adjustment. My #510-468-4891. Give me a call if you would like to discuss.

Jim
N46JP - Q200

Sent from Outer Space

From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser@...>
Sent: Thursday, March 26, 2020 11:56:49 AM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: Re: [Q-List] Brake (Anvil) Rubbing Tire
 
It is so dark up in the wheel well that I couldn't get a good one.  I will take my endoscope camera out there next time and get a photo/video.  

Corbin

On March 26, 2020 at 1:42 PM, Jim Patillo <Logistics_engineering@...> wrote:

You have a pix?
Jim
N46JP - Q200

Sent from Outer Space

From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser@...>
Sent: Thursday, March 26, 2020 11:38:36 AM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: [Q-List] Brake (Anvil) Rubbing Tire
 
Hey guys,

Some of you saw my photos of the dried brake fluid on my brake caliper and now I have another brake related issue I need your experience to help with.  First, I was able to get the caliper all cleaned up and everything looks good so I am going to keep an eye out for small leaks. 

Now my problem is that the anvil (inside part of the brake caliper) is rubbing up against the tire.  No matter how I try and line it up it still rubs the tire just enough to stop it from spinning freely.  I even thought maybe I have too much air in the tire causing it to bulge out too far.  I will double check that in coming days just in case.  I thought I might could get a grinder and grind down the anvil a 1/4 inch or so.....

Any other thoughts?  I am certain the anvil is correctly installed onto the caliper and the bolts have no issues lining up and going in.  

Corbin

--

Corbin 
N33QR




--

Corbin 
N33QR

--

Corbin 
N33QR


Re: Brake (Anvil) Rubbing Tire

Jim Patillo
 

Hi Corbin, I may be able to walk you thru that adjustment. My #510-468-4891. Give me a call if you would like to discuss.

Jim
N46JP - Q200

Sent from Outer Space


From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser@...>
Sent: Thursday, March 26, 2020 11:56:49 AM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: Re: [Q-List] Brake (Anvil) Rubbing Tire
 
It is so dark up in the wheel well that I couldn't get a good one.  I will take my endoscope camera out there next time and get a photo/video.  

Corbin

On March 26, 2020 at 1:42 PM, Jim Patillo <Logistics_engineering@...> wrote:

You have a pix?
Jim
N46JP - Q200

Sent from Outer Space

From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser@...>
Sent: Thursday, March 26, 2020 11:38:36 AM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: [Q-List] Brake (Anvil) Rubbing Tire
 
Hey guys,

Some of you saw my photos of the dried brake fluid on my brake caliper and now I have another brake related issue I need your experience to help with.  First, I was able to get the caliper all cleaned up and everything looks good so I am going to keep an eye out for small leaks. 

Now my problem is that the anvil (inside part of the brake caliper) is rubbing up against the tire.  No matter how I try and line it up it still rubs the tire just enough to stop it from spinning freely.  I even thought maybe I have too much air in the tire causing it to bulge out too far.  I will double check that in coming days just in case.  I thought I might could get a grinder and grind down the anvil a 1/4 inch or so.....

Any other thoughts?  I am certain the anvil is correctly installed onto the caliper and the bolts have no issues lining up and going in.  

Corbin

--

Corbin 
N33QR




--

Corbin 
N33QR


Re: Brake (Anvil) Rubbing Tire

Corbin
 

That would certainly be an easy fix.  These were the size on before and on the right side without issue.  Nonetheless, I could look into the width difference between the two and go from there.

Corbin

On Mar 26, 2020, at 3:40 PM, David J. Gall <David@...> wrote:


Corbin,

I think the 5.00 x 5 tire size is half your trouble. The 4.00 x 5 would be narrower yielding more clearance from sidewall to caliper. 

David J. Gall

On Mar 26, 2020, at 11:38 AM, Corbin via Groups.Io <c_geiser@...> wrote:


Hey guys,

Some of you saw my photos of the dried brake fluid on my brake caliper and now I have another brake related issue I need your experience to help with.  First, I was able to get the caliper all cleaned up and everything looks good so I am going to keep an eye out for small leaks. 

Now my problem is that the anvil (inside part of the brake caliper) is rubbing up against the tire.  No matter how I try and line it up it still rubs the tire just enough to stop it from spinning freely.  I even thought maybe I have too much air in the tire causing it to bulge out too far.  I will double check that in coming days just in case.  I thought I might could get a grinder and grind down the anvil a 1/4 inch or so.....

Any other thoughts?  I am certain the anvil is correctly installed onto the caliper and the bolts have no issues lining up and going in.  

Corbin

--

Corbin 
N33QR

--

Corbin 
N33QR


Re: Brake (Anvil) Rubbing Tire

David J. Gall
 

Corbin,

I think the 5.00 x 5 tire size is half your trouble. The 4.00 x 5 would be narrower yielding more clearance from sidewall to caliper. 

David J. Gall

On Mar 26, 2020, at 11:38 AM, Corbin via Groups.Io <c_geiser@...> wrote:


Hey guys,

Some of you saw my photos of the dried brake fluid on my brake caliper and now I have another brake related issue I need your experience to help with.  First, I was able to get the caliper all cleaned up and everything looks good so I am going to keep an eye out for small leaks. 

Now my problem is that the anvil (inside part of the brake caliper) is rubbing up against the tire.  No matter how I try and line it up it still rubs the tire just enough to stop it from spinning freely.  I even thought maybe I have too much air in the tire causing it to bulge out too far.  I will double check that in coming days just in case.  I thought I might could get a grinder and grind down the anvil a 1/4 inch or so.....

Any other thoughts?  I am certain the anvil is correctly installed onto the caliper and the bolts have no issues lining up and going in.  

Corbin

--

Corbin 
N33QR


Re: Brake (Anvil) Rubbing Tire

Jay Scheevel
 

That’s good. A photo would be very helpful.

 

Cheers,

Jay

 

From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of Corbin via Groups.Io
Sent: Thursday, March 26, 2020 12:57 PM
To: main@Q-List.groups.io
Subject: Re: [Q-List] Brake (Anvil) Rubbing Tire

 

It is so dark up in the wheel well that I couldn't get a good one.  I will take my endoscope camera out there next time and get a photo/video.  

 

Corbin


On March 26, 2020 at 1:42 PM, Jim Patillo <Logistics_engineering@...> wrote:

You have a pix?

Jim

N46JP - Q200

 

Sent from Outer Space


From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser@...>
Sent: Thursday, March 26, 2020 11:38:36 AM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: [Q-List] Brake (Anvil) Rubbing Tire

 

Hey guys,

 

Some of you saw my photos of the dried brake fluid on my brake caliper and now I have another brake related issue I need your experience to help with.  First, I was able to get the caliper all cleaned up and everything looks good so I am going to keep an eye out for small leaks. 

 

Now my problem is that the anvil (inside part of the brake caliper) is rubbing up against the tire.  No matter how I try and line it up it still rubs the tire just enough to stop it from spinning freely.  I even thought maybe I have too much air in the tire causing it to bulge out too far.  I will double check that in coming days just in case.  I thought I might could get a grinder and grind down the anvil a 1/4 inch or so.....

 

Any other thoughts?  I am certain the anvil is correctly installed onto the caliper and the bolts have no issues lining up and going in.  

 

Corbin


--

Corbin 
N33QR

 

 


--

Corbin 
N33QR


Re: Brake (Anvil) Rubbing Tire

Corbin
 

I have Air Hawk 500 x 5 4 ply tires.

Corbin

Which size tire do you have installed? I'm showing 4.00-5 on mine.

image.png

On Thu, Mar 26, 2020 at 3:11 PM Corbin via Groups.Io <c_geiser=icloud.com@groups.io> wrote:
Actually, I have one after-all...it is a large file for email so I uploaded as an unlisted video on YT:  https://youtu.be/R7v9q9lUnkU

Corbin Ge!ser

On March 26, 2020 at 1:57 PM, "Corbin via Groups.Io" <c_geiser=icloud.com@groups.io> wrote:

It is so dark up in the wheel well that I couldn't get a good one.  I will take my endoscope camera out there next time and get a photo/video.  

Corbin

On March 26, 2020 at 1:42 PM, Jim Patillo <Logistics_engineering@...> wrote:

You have a pix?
Jim
N46JP - Q200

Sent from Outer Space

From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser=icloud.com@groups.io>
Sent: Thursday, March 26, 2020 11:38:36 AM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: [Q-List] Brake (Anvil) Rubbing Tire
 
Hey guys,

Some of you saw my photos of the dried brake fluid on my brake caliper and now I have another brake related issue I need your experience to help with.  First, I was able to get the caliper all cleaned up and everything looks good so I am going to keep an eye out for small leaks. 

Now my problem is that the anvil (inside part of the brake caliper) is rubbing up against the tire.  No matter how I try and line it up it still rubs the tire just enough to stop it from spinning freely.  I even thought maybe I have too much air in the tire causing it to bulge out too far.  I will double check that in coming days just in case.  I thought I might could get a grinder and grind down the anvil a 1/4 inch or so.....

Any other thoughts?  I am certain the anvil is correctly installed onto the caliper and the bolts have no issues lining up and going in.  

Corbin

--

Corbin 
N33QR




--

Corbin 
N33QR




--

Corbin 
N33QR






--

Corbin 
N33QR


Re: Brake (Anvil) Rubbing Tire

Corbin
 

Hey Mike - these are the same and are drilled with safety wire.

Corbin

On March 26, 2020 at 2:26 PM, Mike Dwyer <q200pilot@...> wrote:

Oh, the bolts that hold on the rotor on mine have drilled heads and safety wire.  After 30 years I forget if that was per plans...  If one of those bolts comes loose it could ruin your whole day.
Mike Dwyer

YouTube Videos: https://goo.gl/yKEHfK
Q200 Website: http://goo.gl/V8IrJF


On Thu, Mar 26, 2020 at 3:18 PM Mike Dwyer via Groups.Io <q200pilot=gmail.com@groups.io> wrote:
Interesting.  With mine, the caliper assy is much closer to the rotor thus giving you more room.  If this is the problem, you'd have to re drill the mounting holes for your brake assy.  Q's used several systems to mount the caliper.  I forget what system I used (LaRue?), but the Factory Design kinda stunk. 
Mike Dwyer  Q200 N3QP

YouTube Videos: https://goo.gl/yKEHfK
Q200 Website: http://goo.gl/V8IrJF


On Thu, Mar 26, 2020 at 3:11 PM Corbin via Groups.Io <c_geiser=icloud.com@groups.io> wrote:
Actually, I have one after-all...it is a large file for email so I uploaded as an unlisted video on YT:  https://youtu.be/R7v9q9lUnkU

Corbin Ge!ser

On March 26, 2020 at 1:57 PM, "Corbin via Groups.Io" <c_geiser=icloud.com@groups.io> wrote:

It is so dark up in the wheel well that I couldn't get a good one.  I will take my endoscope camera out there next time and get a photo/video.  

Corbin

On March 26, 2020 at 1:42 PM, Jim Patillo <Logistics_engineering@...> wrote:

You have a pix?
Jim
N46JP - Q200

Sent from Outer Space

From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser=icloud.com@groups.io>
Sent: Thursday, March 26, 2020 11:38:36 AM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: [Q-List] Brake (Anvil) Rubbing Tire
 
Hey guys,

Some of you saw my photos of the dried brake fluid on my brake caliper and now I have another brake related issue I need your experience to help with.  First, I was able to get the caliper all cleaned up and everything looks good so I am going to keep an eye out for small leaks. 

Now my problem is that the anvil (inside part of the brake caliper) is rubbing up against the tire.  No matter how I try and line it up it still rubs the tire just enough to stop it from spinning freely.  I even thought maybe I have too much air in the tire causing it to bulge out too far.  I will double check that in coming days just in case.  I thought I might could get a grinder and grind down the anvil a 1/4 inch or so.....

Any other thoughts?  I am certain the anvil is correctly installed onto the caliper and the bolts have no issues lining up and going in.  

Corbin

--

Corbin 
N33QR




--

Corbin 
N33QR




--

Corbin 
N33QR


--

Corbin 
N33QR


Re: Brake (Anvil) Rubbing Tire

Corbin
 

Awesome....I will go back and look at some old photos that I took to make sure I place them just like they were.  I’m 100% sure I took photos the very first time I worked on the brakes.

Corbin

On Mar 26, 2020, at 2:12 PM, Martin Skiby <mskiby@...> wrote:

Corbin,
The washer placement on the mounting of the caliper was key to getting it to not hit when we put it together.  Make sure all of the washers are exactly where they were.  I believe there were washers used as spacers under the caliper mount.

That it about all the advice I have on that one without seeing it.

-----------------------------------------

From: "Corbin via Groups.Io"
To: main@Q-List.groups.io
Cc:
Sent: Thursday March 26 2020 11:56:49AM
Subject: Re: [Q-List] Brake (Anvil) Rubbing Tire

It is so dark up in the wheel well that I couldn't get a good one.  I will take my endoscope camera out there next time and get a photo/video.  

Corbin

On March 26, 2020 at 1:42 PM, Jim Patillo <Logistics_engineering@...> wrote:

You have a pix?
Jim
N46JP - Q200

Sent from Outer Space

From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser@...>
Sent: Thursday, March 26, 2020 11:38:36 AM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: [Q-List] Brake (Anvil) Rubbing Tire
 
Hey guys,

Some of you saw my photos of the dried brake fluid on my brake caliper and now I have another brake related issue I need your experience to help with.  First, I was able to get the caliper all cleaned up and everything looks good so I am going to keep an eye out for small leaks. 

Now my problem is that the anvil (inside part of the brake caliper) is rubbing up against the tire.  No matter how I try and line it up it still rubs the tire just enough to stop it from spinning freely.  I even thought maybe I have too much air in the tire causing it to bulge out too far.  I will double check that in coming days just in case.  I thought I might could get a grinder and grind down the anvil a 1/4 inch or so.....

Any other thoughts?  I am certain the anvil is correctly installed onto the caliper and the bolts have no issues lining up and going in.  

Corbin

--

Corbin 
N33QR




--

Corbin 
N33QR


Re: Brake (Anvil) Rubbing Tire

Mike Dwyer
 

Oh, the bolts that hold on the rotor on mine have drilled heads and safety wire.  After 30 years I forget if that was per plans...  If one of those bolts comes loose it could ruin your whole day.
Mike Dwyer

YouTube Videos: https://goo.gl/yKEHfK
Q200 Website: http://goo.gl/V8IrJF


On Thu, Mar 26, 2020 at 3:18 PM Mike Dwyer via Groups.Io <q200pilot=gmail.com@groups.io> wrote:
Interesting.  With mine, the caliper assy is much closer to the rotor thus giving you more room.  If this is the problem, you'd have to re drill the mounting holes for your brake assy.  Q's used several systems to mount the caliper.  I forget what system I used (LaRue?), but the Factory Design kinda stunk. 
Mike Dwyer  Q200 N3QP

YouTube Videos: https://goo.gl/yKEHfK
Q200 Website: http://goo.gl/V8IrJF


On Thu, Mar 26, 2020 at 3:11 PM Corbin via Groups.Io <c_geiser=icloud.com@groups.io> wrote:
Actually, I have one after-all...it is a large file for email so I uploaded as an unlisted video on YT:  https://youtu.be/R7v9q9lUnkU

Corbin Ge!ser

On March 26, 2020 at 1:57 PM, "Corbin via Groups.Io" <c_geiser=icloud.com@groups.io> wrote:

It is so dark up in the wheel well that I couldn't get a good one.  I will take my endoscope camera out there next time and get a photo/video.  

Corbin

On March 26, 2020 at 1:42 PM, Jim Patillo <Logistics_engineering@...> wrote:

You have a pix?
Jim
N46JP - Q200

Sent from Outer Space

From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser=icloud.com@groups.io>
Sent: Thursday, March 26, 2020 11:38:36 AM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: [Q-List] Brake (Anvil) Rubbing Tire
 
Hey guys,

Some of you saw my photos of the dried brake fluid on my brake caliper and now I have another brake related issue I need your experience to help with.  First, I was able to get the caliper all cleaned up and everything looks good so I am going to keep an eye out for small leaks. 

Now my problem is that the anvil (inside part of the brake caliper) is rubbing up against the tire.  No matter how I try and line it up it still rubs the tire just enough to stop it from spinning freely.  I even thought maybe I have too much air in the tire causing it to bulge out too far.  I will double check that in coming days just in case.  I thought I might could get a grinder and grind down the anvil a 1/4 inch or so.....

Any other thoughts?  I am certain the anvil is correctly installed onto the caliper and the bolts have no issues lining up and going in.  

Corbin

--

Corbin 
N33QR




--

Corbin 
N33QR




--

Corbin 
N33QR


Re: Brake (Anvil) Rubbing Tire

Joe Hood
 

Which size tire do you have installed? I'm showing 4.00-5 on mine.

image.png


On Thu, Mar 26, 2020 at 3:11 PM Corbin via Groups.Io <c_geiser=icloud.com@groups.io> wrote:
Actually, I have one after-all...it is a large file for email so I uploaded as an unlisted video on YT:  https://youtu.be/R7v9q9lUnkU

Corbin Ge!ser

On March 26, 2020 at 1:57 PM, "Corbin via Groups.Io" <c_geiser=icloud.com@groups.io> wrote:

It is so dark up in the wheel well that I couldn't get a good one.  I will take my endoscope camera out there next time and get a photo/video.  

Corbin

On March 26, 2020 at 1:42 PM, Jim Patillo <Logistics_engineering@...> wrote:

You have a pix?
Jim
N46JP - Q200

Sent from Outer Space

From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser=icloud.com@groups.io>
Sent: Thursday, March 26, 2020 11:38:36 AM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: [Q-List] Brake (Anvil) Rubbing Tire
 
Hey guys,

Some of you saw my photos of the dried brake fluid on my brake caliper and now I have another brake related issue I need your experience to help with.  First, I was able to get the caliper all cleaned up and everything looks good so I am going to keep an eye out for small leaks. 

Now my problem is that the anvil (inside part of the brake caliper) is rubbing up against the tire.  No matter how I try and line it up it still rubs the tire just enough to stop it from spinning freely.  I even thought maybe I have too much air in the tire causing it to bulge out too far.  I will double check that in coming days just in case.  I thought I might could get a grinder and grind down the anvil a 1/4 inch or so.....

Any other thoughts?  I am certain the anvil is correctly installed onto the caliper and the bolts have no issues lining up and going in.  

Corbin

--

Corbin 
N33QR




--

Corbin 
N33QR




--

Corbin 
N33QR


Re: Brake (Anvil) Rubbing Tire

Mike Dwyer
 

Interesting.  With mine, the caliper assy is much closer to the rotor thus giving you more room.  If this is the problem, you'd have to re drill the mounting holes for your brake assy.  Q's used several systems to mount the caliper.  I forget what system I used (LaRue?), but the Factory Design kinda stunk. 
Mike Dwyer  Q200 N3QP

YouTube Videos: https://goo.gl/yKEHfK
Q200 Website: http://goo.gl/V8IrJF


On Thu, Mar 26, 2020 at 3:11 PM Corbin via Groups.Io <c_geiser=icloud.com@groups.io> wrote:
Actually, I have one after-all...it is a large file for email so I uploaded as an unlisted video on YT:  https://youtu.be/R7v9q9lUnkU

Corbin Ge!ser

On March 26, 2020 at 1:57 PM, "Corbin via Groups.Io" <c_geiser=icloud.com@groups.io> wrote:

It is so dark up in the wheel well that I couldn't get a good one.  I will take my endoscope camera out there next time and get a photo/video.  

Corbin

On March 26, 2020 at 1:42 PM, Jim Patillo <Logistics_engineering@...> wrote:

You have a pix?
Jim
N46JP - Q200

Sent from Outer Space

From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via Groups.Io <c_geiser=icloud.com@groups.io>
Sent: Thursday, March 26, 2020 11:38:36 AM
To: main@Q-List.groups.io <main@Q-List.groups.io>
Subject: [Q-List] Brake (Anvil) Rubbing Tire
 
Hey guys,

Some of you saw my photos of the dried brake fluid on my brake caliper and now I have another brake related issue I need your experience to help with.  First, I was able to get the caliper all cleaned up and everything looks good so I am going to keep an eye out for small leaks. 

Now my problem is that the anvil (inside part of the brake caliper) is rubbing up against the tire.  No matter how I try and line it up it still rubs the tire just enough to stop it from spinning freely.  I even thought maybe I have too much air in the tire causing it to bulge out too far.  I will double check that in coming days just in case.  I thought I might could get a grinder and grind down the anvil a 1/4 inch or so.....

Any other thoughts?  I am certain the anvil is correctly installed onto the caliper and the bolts have no issues lining up and going in.  

Corbin

--

Corbin 
N33QR




--

Corbin 
N33QR




--

Corbin 
N33QR

4001 - 4020 of 52821