Date   

Re: Slight Damage to Canopy

One Sky Dog
 

No bondo over epoxy It will come off.

On Nov 11, 2020, at 6:44 PM, Jay Scheevel <jay@...> wrote:

I would just use bondo, then sand it down flush, paint it with some matching white urethane (just use a brush and do several coats 20 minutes or so apart). Wait for it to thoroughly dry, then go at it feathering it with 400, 800, 1200 grit wet sanding without working through the paint, then buff it and wax it and you are done. If you get through the paint, then just repeat the process. My 2 cents
Cheers,
Jay
-----Original Message-----
From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of Corbin via groups.io
Sent: Wednesday, November 11, 2020 6:18 PM
To: main@Q-List.groups.io Group Moderators <main@q-list.groups.io>
Subject: [Q-List] Slight Damage to Canopy

What’s the recommended fix for this bit of damage to the canopy edge?  I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy.  But it wasn’t there the last time I flew for certain.






Corbin

--
Corbin
N33QR












Re: Slight Damage to Canopy

Jim Patillo
 

I’m with Phil on this one. It’s a leading edge.

Jim
N46JP Q200

Sent from Outer Space


From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Phil Lankford via groups.io <britmcman@...>
Sent: Wednesday, November 11, 2020 5:37:19 PM
To: main@q-list.groups.io <main@q-list.groups.io>
Subject: Re: [Q-List] Slight Damage to Canopy
 
Mix up a little cotton flox and epoxy and shape it to your liking. Phil
> On Nov 11, 2020, at 5:18 PM, Corbin via groups.io <c_geiser@...> wrote:
>
> What’s the recommended fix for this bit of damage to the canopy edge?  I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy.  But it wasn’t there the last time I flew for certain.
>
>
>
>
>
>
> Corbin
>
> --
> Corbin
> N33QR
>
>
>
>
>
> <image5.jpeg>
> <image6.jpeg>
> <image7.jpeg>







Re: Slight Damage to Canopy

Jay Scheevel
 

I would just use bondo, then sand it down flush, paint it with some matching white urethane (just use a brush and do several coats 20 minutes or so apart). Wait for it to thoroughly dry, then go at it feathering it with 400, 800, 1200 grit wet sanding without working through the paint, then buff it and wax it and you are done. If you get through the paint, then just repeat the process. My 2 cents
Cheers,
Jay

-----Original Message-----
From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of Corbin via groups.io
Sent: Wednesday, November 11, 2020 6:18 PM
To: main@Q-List.groups.io Group Moderators <main@q-list.groups.io>
Subject: [Q-List] Slight Damage to Canopy

What’s the recommended fix for this bit of damage to the canopy edge? I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy. But it wasn’t there the last time I flew for certain.






Corbin

--
Corbin
N33QR


Re: Slight Damage to Canopy

Phil Lankford
 

Mix up a little cotton flox and epoxy and shape it to your liking. Phil

On Nov 11, 2020, at 5:18 PM, Corbin via groups.io <c_geiser=icloud.com@groups.io> wrote:

What’s the recommended fix for this bit of damage to the canopy edge? I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy. But it wasn’t there the last time I flew for certain.






Corbin

--
Corbin
N33QR





<image5.jpeg>
<image6.jpeg>
<image7.jpeg>


Slight Damage to Canopy

Corbin
 

What’s the recommended fix for this bit of damage to the canopy edge? I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy. But it wasn’t there the last time I flew for certain.






Corbin

--
Corbin
N33QR


Re: Q-2 /Q-200 parts for sale almost free

Mike Steinsland
 

I'm looking for a top and bottom  cowl
How much?
Mike
705-774-3275

On Wed, Nov 11, 2020, 2:15 PM Stan Susman, <stanpfa@...> wrote:
Gang, I have some factory new Q-2 parts for sale. I need them gone fast. If you belong to a EAA chapter of have another 501c3 org I will donate them.
top and bottom fuse.
top and bottom tail cone 
most bulkheads
canopy
top and bottom cowl
I also have some 4A-084 engines (2 new) and prop hubs
e-mail stanpfa@... or call 831-334-3035 near Watsonville ca
thanks


Re: Q-2 /Q-200 parts for sale almost free

Martin Skiby
 

I have a nearly complete plane.  Wings, fuselage with tinted canopy installed, most all the hardware, wings with the wadalow layup.  LS canard, control surfaces etc.  No cowlings.

There is a bunch here and needs to be complete.  e-mail me at mskiby@... and I can send photos.




-----------------------------------------

From: "Anthony P"
To: main@Q-List.groups.io
Cc:
Sent: Wednesday November 11 2020 12:27:12PM
Subject: Re: [Q-List] Q-2 /Q-200 parts for sale almost free

Mr. Martin Skiby, where are your parts located?


Re: Q-2 /Q-200 parts for sale almost free

Martin Skiby
 

Bakersfield, CA

-----------------------------------------

From: "Anthony P"
To: main@Q-List.groups.io
Cc:
Sent: Wednesday November 11 2020 12:27:12PM
Subject: Re: [Q-List] Q-2 /Q-200 parts for sale almost free

Mr. Martin Skiby, where are your parts located?


Re: Q-2 /Q-200 parts for sale almost free

Anthony P
 

Mr. Martin Skiby, where are your parts located?


Re: Q-2 /Q-200 parts for sale almost free

Martin Skiby
 

I have a set of wings and the LS canard has a spar in it.  But I don't want to break up the kit so if he wants they he would need to buy the whole thing.

Then lots of spare parts he would have :)


-----------------------------------------

From: "Bruce Crain"
To: main@Q-List.groups.io
Cc:
Sent: Wednesday November 11 2020 11:20:40AM
Subject: Re: [Q-List] Q-2 /Q-200 parts for sale almost free

Cody Craig needs a carbon fiber spar if you  have one!
Bruce


---------- Original Message ----------
From: "Stan Susman" <stanpfa@...>
To: main@Q-List.groups.io
Subject: [Q-List] Q-2 /Q-200 parts for sale almost free
Date: Wed, 11 Nov 2020 11:14:53 -0800

Gang, I have some factory new Q-2 parts for sale. I need them gone fast. If you belong to a EAA chapter of have another 501c3 org I will donate them.
top and bottom fuse.
top and bottom tail cone 
most bulkheads
canopy
top and bottom cowl
I also have some 4A-084 engines (2 new) and prop hubs
e-mail stanpfa@... or call 831-334-3035 near Watsonville ca
thanks




Q2 misc brake parts

Jerry Marstall <jnmarstall@...>
 

Anyone interested?  Contact me at jnmarstall@... 


Re: Q-2 /Q-200 parts for sale almost free

Jay Scheevel
 

Hi Stan,

 

WE have a non profit group (501c3) called HAWK Aviators, that has kids learning to build airplanes and fly airplanes, here in Mack Colorado (https://hawkaviators.org/). I just forwarded your note to them, so if they are interested, they will contact you pronto.

 

Cheers,

Jay

 

From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of Bruce Crain
Sent: Wednesday, November 11, 2020 12:18 PM
To: main@Q-List.groups.io
Subject: Re: [Q-List] Q-2 /Q-200 parts for sale almost free

 

Cody Craig needs a carbon fiber spar if you  have one!

Bruce

---------- Original Message ----------
From: "Stan Susman" <stanpfa@...>
To: main@Q-List.groups.io
Subject: [Q-List] Q-2 /Q-200 parts for sale almost free
Date: Wed, 11 Nov 2020 11:14:53 -0800

Gang, I have some factory new Q-2 parts for sale. I need them gone fast. If you belong to a EAA chapter of have another 501c3 org I will donate them.
top and bottom fuse.
top and bottom tail cone 
most bulkheads
canopy
top and bottom cowl
I also have some 4A-084 engines (2 new) and prop hubs
e-mail stanpfa@... or call 831-334-3035 near Watsonville ca
thanks

 


Re: Q-2 /Q-200 parts for sale almost free

Stan Susman
 

no wing parts, thanks

On Wednesday, November 11, 2020, 11:20:41 AM PST, Bruce Crain <jcrain2@...> wrote:


Cody Craig needs a carbon fiber spar if you  have one!
Bruce

---------- Original Message ----------
From: "Stan Susman" <stanpfa@...>
To: main@Q-List.groups.io
Subject: [Q-List] Q-2 /Q-200 parts for sale almost free
Date: Wed, 11 Nov 2020 11:14:53 -0800

Gang, I have some factory new Q-2 parts for sale. I need them gone fast. If you belong to a EAA chapter of have another 501c3 org I will donate them.
top and bottom fuse.
top and bottom tail cone 
most bulkheads
canopy
top and bottom cowl
I also have some 4A-084 engines (2 new) and prop hubs
e-mail stanpfa@... or call 831-334-3035 near Watsonville ca
thanks


Re: Q-2 /Q-200 parts for sale almost free

Bruce Crain
 

Cody Craig needs a carbon fiber spar if you  have one!
Bruce


---------- Original Message ----------
From: "Stan Susman" <stanpfa@...>
To: main@Q-List.groups.io
Subject: [Q-List] Q-2 /Q-200 parts for sale almost free
Date: Wed, 11 Nov 2020 11:14:53 -0800

Gang, I have some factory new Q-2 parts for sale. I need them gone fast. If you belong to a EAA chapter of have another 501c3 org I will donate them.
top and bottom fuse.
top and bottom tail cone 
most bulkheads
canopy
top and bottom cowl
I also have some 4A-084 engines (2 new) and prop hubs
e-mail stanpfa@... or call 831-334-3035 near Watsonville ca
thanks




Q-2 /Q-200 parts for sale almost free

Stan Susman
 

Gang, I have some factory new Q-2 parts for sale. I need them gone fast. If you belong to a EAA chapter of have another 501c3 org I will donate them.
top and bottom fuse.
top and bottom tail cone 
most bulkheads
canopy
top and bottom cowl
I also have some 4A-084 engines (2 new) and prop hubs
e-mail stanpfa@... or call 831-334-3035 near Watsonville ca
thanks


File /Pilot Operating Handbooks, POH/Q2 QAC POH.pdf uploaded #file-notice

main@Q-List.groups.io Notification <noreply@...>
 

The following files have been uploaded to the Files area of the main@Q-List.groups.io group.

By: Sam Hoskins

Description:
The factory Q-2 POH


Re: Q1 Bill of material - Alternative supplier and Technical Specification - Technical data sheet

Gabor Halasi <kishal63@...>
 

Huge! Many thanks Eugen!

I am about to start my q1 project, shop (garage) almost completed, tooling is missing. 

Regards,

Gabor
from Hungary

On Tue, Nov 10, 2020 at 8:19 PM Eugen Pilarski <interbus@...> wrote:
Dear Q-Experts,

please find the link to the files I create to upload alternative supplier and technical Specification/technical data sheet to fill the bill of material with more information during my investigation to build a Quickie. Please fell free to upload your sources and tech. Specs also.

click me

Best regards

Eugen


Q1 Bill of material - Alternative supplier and Technical Specification - Technical data sheet

Eugen Pilarski
 

Dear Q-Experts,

please find the link to the files I create to upload alternative supplier and technical Specification/technical data sheet to fill the bill of material with more information during my investigation to build a Quickie. Please fell free to upload your sources and tech. Specs also.

click me

Best regards

Eugen


Re: Electronic Ignition Install - No Spark from Coils

Martin Skiby
 

My apologies.  Yes sorry I should have started earlier in the conversation.

Carry on.  Interested to see the outcome.

Martin

 


On Nov 10, 2020, at 8:43 AM, Corbin via groups.io <c_geiser@...> wrote:


Martin,

I think you are missing the first update from this morning (it is the one you replied to).  Setting up per instructions and firing it up with the starter did not work.  The rocking of the prop back and forth was in response to the question of what Klaus recommended.  We tried both.

Corbin

On November 10, 2020 at 9:03 AM, Martin Skiby <mskiby@...> wrote:

Dude you are fighting yourself on this.  Set it up as the instructions show and fire it up.  Rocking the prop back and forth and trying to get a spark is frustrating you.  Try using the starter and see if it fires up and runs.  That is the only way to know.  You will wear yourself out trying to trigger a sensor that needs 500rpm or so to do just to see if you have a spark.  You will know right away if it starts.

MY opinion.


-----------------------------------------

From: "Corbin via groups.io"
To: main@Q-List.groups.io
Cc:
Sent: Tuesday November 10 2020 4:40:02AM
Subject: Re: [Q-List] Electronic Ignition Install - No Spark from Coils

Hey Jim,

The lower RPM is actually the main reason I was installing this ignition system.  Klaus says it will add RPM but I think he must mean in cruise and not idle.

Klaus seemed to think we had installed everything correctly and that we didn't rock the prop fast enough.  We tried again and then used the starter and still couldn't get a spark.  I am going to reach out to him again today to see if I should try new magnet sensors.

Corbin

On November 9, 2020 at 11:02 PM, Jim Patillo <Logistics_engineering@...> wrote:

Corbin, you will not regret putting in Lightspeed electronic ignitions once you get them working. Hang in there, you’ll get it.
You’ll be able to idle at 450 rpm which is good for landings on shorter runways and can run faster higher up.

What’s Klaus offering in the way of help?

Jim
N46JP Q200

Sent from Outer Space

From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via groups.io <c_geiser@...>
Sent: Monday, November 9, 2020 7:17:21 PM
To: main@q-list.groups.io <main@q-list.groups.io>
Subject: Re: [Q-List] Electronic Ignition Install - No Spark from Coils
 
Well, no luck tonight.  No spark rocking back and forth at #1 TDC, no luck rotating prop faster, and no luck having the starter have a go at it.  

At this point, I’m assuming the sensor(s) are bad.  Ugh.  Wishing I had never tried upgrading to electronic ignition at this point and ready to put the mags back on.

Corbin

On Nov 9, 2020, at 1:56 PM, Corbin via groups.io <c_geiser@...> wrote:

Follow up to keep records of information learned.  

Klaus' best guess is that we just need to rock the prop a bit faster.  He believes we have everything else correct.  We will try that tonight and, if no luck, might just let the starter give it a go in order to see if it can get a spark from the coil.  Leads are not connected, of course.

--

Corbin 
N33QR

--

Corbin 
N33QR

--

Corbin 
N33QR


Re: Electronic Ignition Install - No Spark from Coils

Corbin
 

Martin,

I think you are missing the first update from this morning (it is the one you replied to).  Setting up per instructions and firing it up with the starter did not work.  The rocking of the prop back and forth was in response to the question of what Klaus recommended.  We tried both.

Corbin

On November 10, 2020 at 9:03 AM, Martin Skiby <mskiby@...> wrote:

Dude you are fighting yourself on this.  Set it up as the instructions show and fire it up.  Rocking the prop back and forth and trying to get a spark is frustrating you.  Try using the starter and see if it fires up and runs.  That is the only way to know.  You will wear yourself out trying to trigger a sensor that needs 500rpm or so to do just to see if you have a spark.  You will know right away if it starts.

MY opinion.


-----------------------------------------

From: "Corbin via groups.io"
To: main@Q-List.groups.io
Cc:
Sent: Tuesday November 10 2020 4:40:02AM
Subject: Re: [Q-List] Electronic Ignition Install - No Spark from Coils

Hey Jim,

The lower RPM is actually the main reason I was installing this ignition system.  Klaus says it will add RPM but I think he must mean in cruise and not idle.

Klaus seemed to think we had installed everything correctly and that we didn't rock the prop fast enough.  We tried again and then used the starter and still couldn't get a spark.  I am going to reach out to him again today to see if I should try new magnet sensors.

Corbin

On November 9, 2020 at 11:02 PM, Jim Patillo <Logistics_engineering@...> wrote:

Corbin, you will not regret putting in Lightspeed electronic ignitions once you get them working. Hang in there, you’ll get it.
You’ll be able to idle at 450 rpm which is good for landings on shorter runways and can run faster higher up.

What’s Klaus offering in the way of help?

Jim
N46JP Q200

Sent from Outer Space

From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Corbin via groups.io <c_geiser@...>
Sent: Monday, November 9, 2020 7:17:21 PM
To: main@q-list.groups.io <main@q-list.groups.io>
Subject: Re: [Q-List] Electronic Ignition Install - No Spark from Coils
 
Well, no luck tonight.  No spark rocking back and forth at #1 TDC, no luck rotating prop faster, and no luck having the starter have a go at it.  

At this point, I’m assuming the sensor(s) are bad.  Ugh.  Wishing I had never tried upgrading to electronic ignition at this point and ready to put the mags back on.

Corbin

On Nov 9, 2020, at 1:56 PM, Corbin via groups.io <c_geiser@...> wrote:

Follow up to keep records of information learned.  

Klaus' best guess is that we just need to rock the prop a bit faster.  He believes we have everything else correct.  We will try that tonight and, if no luck, might just let the starter give it a go in order to see if it can get a spark from the coil.  Leads are not connected, of course.

--

Corbin 
N33QR

--

Corbin 
N33QR

--

Corbin 
N33QR

2301 - 2320 of 52978