Date   

Re: Slight Damage to Canopy

Sam Hoskins
 

Something that small and non-structural I would use JB Weld.

Sam 

On Wed, Nov 11, 2020, 9:30 PM One Sky Dog via groups.io <Oneskydog=aol.com@groups.io> wrote:
No bondo over epoxy It will come off.

Charlie


On Nov 11, 2020, at 6:44 PM, Jay Scheevel <jay@...> wrote:

I would just use bondo, then sand it down flush, paint it with some matching white urethane (just use a brush and do several coats 20 minutes or so apart). Wait for it to thoroughly dry, then go at it feathering it with 400, 800, 1200 grit wet sanding without working through the paint, then buff it and wax it and you are done. If you get through the paint, then just repeat the process. My 2 cents
Cheers,
Jay
-----Original Message-----
From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of Corbin via groups.io
Sent: Wednesday, November 11, 2020 6:18 PM
To: main@Q-List.groups.io Group Moderators <main@q-list.groups.io>
Subject: [Q-List] Slight Damage to Canopy

What’s the recommended fix for this bit of damage to the canopy edge?  I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy.  But it wasn’t there the last time I flew for certain.






Corbin

--
Corbin
N33QR












Re: Slight Damage to Canopy

Jay Scheevel
 

Dang, I knew I shouldn't have glued my wings on with that stuff!

Sent from my Verizon Wireless 4G LTE DROID


"One Sky Dog via groups.io" <Oneskydog@...> wrote:

No bondo over epoxy It will come off.

On Nov 11, 2020, at 6:44 PM, Jay Scheevel <jay@...> wrote:

I would just use bondo, then sand it down flush, paint it with some matching white urethane (just use a brush and do several coats 20 minutes or so apart). Wait for it to thoroughly dry, then go at it feathering it with 400, 800, 1200 grit wet sanding without working through the paint, then buff it and wax it and you are done. If you get through the paint, then just repeat the process. My 2 cents
Cheers,
Jay
-----Original Message-----
From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of Corbin via groups.io
Sent: Wednesday, November 11, 2020 6:18 PM
To: main@Q-List.groups.io Group Moderators <main@q-list.groups.io>
Subject: [Q-List] Slight Damage to Canopy

What’s the recommended fix for this bit of damage to the canopy edge?  I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy.  But it wasn’t there the last time I flew for certain.






Corbin

--
Corbin
N33QR












Re: Slight Damage to Canopy

One Sky Dog
 

No bondo over epoxy It will come off.

On Nov 11, 2020, at 6:44 PM, Jay Scheevel <jay@...> wrote:

I would just use bondo, then sand it down flush, paint it with some matching white urethane (just use a brush and do several coats 20 minutes or so apart). Wait for it to thoroughly dry, then go at it feathering it with 400, 800, 1200 grit wet sanding without working through the paint, then buff it and wax it and you are done. If you get through the paint, then just repeat the process. My 2 cents
Cheers,
Jay
-----Original Message-----
From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of Corbin via groups.io
Sent: Wednesday, November 11, 2020 6:18 PM
To: main@Q-List.groups.io Group Moderators <main@q-list.groups.io>
Subject: [Q-List] Slight Damage to Canopy

What’s the recommended fix for this bit of damage to the canopy edge?  I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy.  But it wasn’t there the last time I flew for certain.






Corbin

--
Corbin
N33QR












Re: Slight Damage to Canopy

Jim Patillo
 

I’m with Phil on this one. It’s a leading edge.

Jim
N46JP Q200

Sent from Outer Space


From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Phil Lankford via groups.io <britmcman@...>
Sent: Wednesday, November 11, 2020 5:37:19 PM
To: main@q-list.groups.io <main@q-list.groups.io>
Subject: Re: [Q-List] Slight Damage to Canopy
 
Mix up a little cotton flox and epoxy and shape it to your liking. Phil
> On Nov 11, 2020, at 5:18 PM, Corbin via groups.io <c_geiser@...> wrote:
>
> What’s the recommended fix for this bit of damage to the canopy edge?  I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy.  But it wasn’t there the last time I flew for certain.
>
>
>
>
>
>
> Corbin
>
> --
> Corbin
> N33QR
>
>
>
>
>
> <image5.jpeg>
> <image6.jpeg>
> <image7.jpeg>







Re: Slight Damage to Canopy

Jay Scheevel
 

I would just use bondo, then sand it down flush, paint it with some matching white urethane (just use a brush and do several coats 20 minutes or so apart). Wait for it to thoroughly dry, then go at it feathering it with 400, 800, 1200 grit wet sanding without working through the paint, then buff it and wax it and you are done. If you get through the paint, then just repeat the process. My 2 cents
Cheers,
Jay

-----Original Message-----
From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of Corbin via groups.io
Sent: Wednesday, November 11, 2020 6:18 PM
To: main@Q-List.groups.io Group Moderators <main@q-list.groups.io>
Subject: [Q-List] Slight Damage to Canopy

What’s the recommended fix for this bit of damage to the canopy edge? I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy. But it wasn’t there the last time I flew for certain.






Corbin

--
Corbin
N33QR


Re: Slight Damage to Canopy

britmcman99
 

Mix up a little cotton flox and epoxy and shape it to your liking. Phil

On Nov 11, 2020, at 5:18 PM, Corbin via groups.io <c_geiser=icloud.com@groups.io> wrote:

What’s the recommended fix for this bit of damage to the canopy edge? I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy. But it wasn’t there the last time I flew for certain.






Corbin

--
Corbin
N33QR





<image5.jpeg>
<image6.jpeg>
<image7.jpeg>


Slight Damage to Canopy

Corbin
 

What’s the recommended fix for this bit of damage to the canopy edge? I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy. But it wasn’t there the last time I flew for certain.






Corbin

--
Corbin
N33QR


Re: Q-2 /Q-200 parts for sale almost free

Mike Steinsland
 

I'm looking for a top and bottom  cowl
How much?
Mike
705-774-3275

On Wed, Nov 11, 2020, 2:15 PM Stan Susman, <stanpfa@...> wrote:
Gang, I have some factory new Q-2 parts for sale. I need them gone fast. If you belong to a EAA chapter of have another 501c3 org I will donate them.
top and bottom fuse.
top and bottom tail cone 
most bulkheads
canopy
top and bottom cowl
I also have some 4A-084 engines (2 new) and prop hubs
e-mail stanpfa@... or call 831-334-3035 near Watsonville ca
thanks


Re: Q-2 /Q-200 parts for sale almost free

Martin Skiby
 

I have a nearly complete plane.  Wings, fuselage with tinted canopy installed, most all the hardware, wings with the wadalow layup.  LS canard, control surfaces etc.  No cowlings.

There is a bunch here and needs to be complete.  e-mail me at mskiby@... and I can send photos.




-----------------------------------------

From: "Anthony P"
To: main@Q-List.groups.io
Cc:
Sent: Wednesday November 11 2020 12:27:12PM
Subject: Re: [Q-List] Q-2 /Q-200 parts for sale almost free

Mr. Martin Skiby, where are your parts located?


Re: Q-2 /Q-200 parts for sale almost free

Martin Skiby
 

Bakersfield, CA

-----------------------------------------

From: "Anthony P"
To: main@Q-List.groups.io
Cc:
Sent: Wednesday November 11 2020 12:27:12PM
Subject: Re: [Q-List] Q-2 /Q-200 parts for sale almost free

Mr. Martin Skiby, where are your parts located?


Re: Q-2 /Q-200 parts for sale almost free

Anthony P
 

Mr. Martin Skiby, where are your parts located?


Re: Q-2 /Q-200 parts for sale almost free

Martin Skiby
 

I have a set of wings and the LS canard has a spar in it.  But I don't want to break up the kit so if he wants they he would need to buy the whole thing.

Then lots of spare parts he would have :)


-----------------------------------------

From: "Bruce Crain"
To: main@Q-List.groups.io
Cc:
Sent: Wednesday November 11 2020 11:20:40AM
Subject: Re: [Q-List] Q-2 /Q-200 parts for sale almost free

Cody Craig needs a carbon fiber spar if you  have one!
Bruce


---------- Original Message ----------
From: "Stan Susman" <stanpfa@...>
To: main@Q-List.groups.io
Subject: [Q-List] Q-2 /Q-200 parts for sale almost free
Date: Wed, 11 Nov 2020 11:14:53 -0800

Gang, I have some factory new Q-2 parts for sale. I need them gone fast. If you belong to a EAA chapter of have another 501c3 org I will donate them.
top and bottom fuse.
top and bottom tail cone 
most bulkheads
canopy
top and bottom cowl
I also have some 4A-084 engines (2 new) and prop hubs
e-mail stanpfa@... or call 831-334-3035 near Watsonville ca
thanks




Q2 misc brake parts

Jerry Marstall <jnmarstall@...>
 

Anyone interested?  Contact me at jnmarstall@... 


Re: Q-2 /Q-200 parts for sale almost free

Jay Scheevel
 

Hi Stan,

 

WE have a non profit group (501c3) called HAWK Aviators, that has kids learning to build airplanes and fly airplanes, here in Mack Colorado (https://hawkaviators.org/). I just forwarded your note to them, so if they are interested, they will contact you pronto.

 

Cheers,

Jay

 

From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of Bruce Crain
Sent: Wednesday, November 11, 2020 12:18 PM
To: main@Q-List.groups.io
Subject: Re: [Q-List] Q-2 /Q-200 parts for sale almost free

 

Cody Craig needs a carbon fiber spar if you  have one!

Bruce

---------- Original Message ----------
From: "Stan Susman" <stanpfa@...>
To: main@Q-List.groups.io
Subject: [Q-List] Q-2 /Q-200 parts for sale almost free
Date: Wed, 11 Nov 2020 11:14:53 -0800

Gang, I have some factory new Q-2 parts for sale. I need them gone fast. If you belong to a EAA chapter of have another 501c3 org I will donate them.
top and bottom fuse.
top and bottom tail cone 
most bulkheads
canopy
top and bottom cowl
I also have some 4A-084 engines (2 new) and prop hubs
e-mail stanpfa@... or call 831-334-3035 near Watsonville ca
thanks

 


Re: Q-2 /Q-200 parts for sale almost free

Stan Susman
 

no wing parts, thanks

On Wednesday, November 11, 2020, 11:20:41 AM PST, Bruce Crain <jcrain2@...> wrote:


Cody Craig needs a carbon fiber spar if you  have one!
Bruce

---------- Original Message ----------
From: "Stan Susman" <stanpfa@...>
To: main@Q-List.groups.io
Subject: [Q-List] Q-2 /Q-200 parts for sale almost free
Date: Wed, 11 Nov 2020 11:14:53 -0800

Gang, I have some factory new Q-2 parts for sale. I need them gone fast. If you belong to a EAA chapter of have another 501c3 org I will donate them.
top and bottom fuse.
top and bottom tail cone 
most bulkheads
canopy
top and bottom cowl
I also have some 4A-084 engines (2 new) and prop hubs
e-mail stanpfa@... or call 831-334-3035 near Watsonville ca
thanks


Re: Q-2 /Q-200 parts for sale almost free

Bruce Crain
 

Cody Craig needs a carbon fiber spar if you  have one!
Bruce


---------- Original Message ----------
From: "Stan Susman" <stanpfa@...>
To: main@Q-List.groups.io
Subject: [Q-List] Q-2 /Q-200 parts for sale almost free
Date: Wed, 11 Nov 2020 11:14:53 -0800

Gang, I have some factory new Q-2 parts for sale. I need them gone fast. If you belong to a EAA chapter of have another 501c3 org I will donate them.
top and bottom fuse.
top and bottom tail cone 
most bulkheads
canopy
top and bottom cowl
I also have some 4A-084 engines (2 new) and prop hubs
e-mail stanpfa@... or call 831-334-3035 near Watsonville ca
thanks




Q-2 /Q-200 parts for sale almost free

Stan Susman
 

Gang, I have some factory new Q-2 parts for sale. I need them gone fast. If you belong to a EAA chapter of have another 501c3 org I will donate them.
top and bottom fuse.
top and bottom tail cone 
most bulkheads
canopy
top and bottom cowl
I also have some 4A-084 engines (2 new) and prop hubs
e-mail stanpfa@... or call 831-334-3035 near Watsonville ca
thanks


File /Pilot Operating Handbooks, POH/Q2 QAC POH.pdf uploaded #file-notice

main@Q-List.groups.io Notification <noreply@...>
 

The following files have been uploaded to the Files area of the main@Q-List.groups.io group.

By: Sam Hoskins

Description:
The factory Q-2 POH


Re: Q1 Bill of material - Alternative supplier and Technical Specification - Technical data sheet

Gabor Halasi <kishal63@...>
 

Huge! Many thanks Eugen!

I am about to start my q1 project, shop (garage) almost completed, tooling is missing. 

Regards,

Gabor
from Hungary

On Tue, Nov 10, 2020 at 8:19 PM Eugen Pilarski <interbus@...> wrote:
Dear Q-Experts,

please find the link to the files I create to upload alternative supplier and technical Specification/technical data sheet to fill the bill of material with more information during my investigation to build a Quickie. Please fell free to upload your sources and tech. Specs also.

click me

Best regards

Eugen


Q1 Bill of material - Alternative supplier and Technical Specification - Technical data sheet

Eugen Pilarski
 

Dear Q-Experts,

please find the link to the files I create to upload alternative supplier and technical Specification/technical data sheet to fill the bill of material with more information during my investigation to build a Quickie. Please fell free to upload your sources and tech. Specs also.

click me

Best regards

Eugen

4121 - 4140 of 54800