Date   

Re: Electronic Ignition Install - No Spark from Coils

Corbin
 

We are closer to .030" in the range of .030" to .060" since the crankshaft on the O-200 doesn't move back and forth much.   I want to say we left it around .032".
--

Corbin 
N33QR


Re: Electronic Ignition Install - No Spark from Coils

Jim Patillo
 

How much gap do you have between the magnet and pickup?

Jim
N46JP Q200


Re: Q-2 /Q-200 parts for sale almost free

Kyle Voltz <kvoltz21@...>
 

Boy could I use the tail cone parts, but I’m in Oshkosh :/

Kyle D. Voltz
20 Castle Ct. Oshkosh, WI 54902
Mobile309.945.5188 | EmailKvoltz21@...
 
Commercial Pilot ASEL/AMEL
Instrument | Complex | Tailwheel | High Performance
EAA Flight Advisor 880499
 


On Nov 11, 2020, at 2:23 PM, Martin Skiby <mskiby@...> wrote:

I have a set of wings and the LS canard has a spar in it.  But I don't want to break up the kit so if he wants they he would need to buy the whole thing.

Then lots of spare parts he would have :)


-----------------------------------------

From: "Bruce Crain"
To: main@Q-List.groups.io
Cc:
Sent: Wednesday November 11 2020 11:20:40AM
Subject: Re: [Q-List] Q-2 /Q-200 parts for sale almost free

Cody Craig needs a carbon fiber spar if you  have one!
Bruce

---------- Original Message ----------
From: "Stan Susman" <stanpfa@...>
To: main@Q-List.groups.io
Subject: [Q-List] Q-2 /Q-200 parts for sale almost free
Date: Wed, 11 Nov 2020 11:14:53 -0800

Gang, I have some factory new Q-2 parts for sale. I need them gone fast. If you belong to a EAA chapter of have another 501c3 org I will donate them.
top and bottom fuse.
top and bottom tail cone 
most bulkheads
canopy
top and bottom cowl
I also have some 4A-084 engines (2 new) and prop hubs
e-mail stanpfa@... or call 831-334-3035 near Watsonville ca
thanks




Re: Electronic Ignition Install - No Spark from Coils

Corbin
 

Just in case anyone was curious about an update, I thought I would let you know still no luck after trying again last night.

Klaus recommended we troubleshoot the input signal test but that passed as well-meaning the current is flowing from the sensor to the input on the ignition boxes.  Just to be certain, we went through all troubleshooting steps again with no luck.  Sensor alignment triple checked, 5v passes to input and we have output back to coils.  At this point, all signs seem to be pointing towards the magnet plate so we the only thing left to try, that we could think of, is passing the South pole of a magnet by the sensor to see if we can get the volt drop.  

In the meantime, we will see what else Klaus recommends.

--

Corbin 
N33QR


Re: Q-2 /Q-200 parts for sale almost free

 

Martin, could you email me cody.craig1985@.... I'm interested as not only do I have my plane to build, but a friend wants to build one as well. This would be great.


Re: Slight Damage to Canopy

Mike Steinsland
 

I've been in autobody all my life.
Go with the flox, bondo will just break off the edge.

On Wed, Nov 11, 2020 at 10:57 PM Sam Hoskins <sam.hoskins@...> wrote:
Something that small and non-structural I would use JB Weld.

Sam 

On Wed, Nov 11, 2020, 9:30 PM One Sky Dog via groups.io <Oneskydog=aol.com@groups.io> wrote:
No bondo over epoxy It will come off.

Charlie


On Nov 11, 2020, at 6:44 PM, Jay Scheevel <jay@...> wrote:

I would just use bondo, then sand it down flush, paint it with some matching white urethane (just use a brush and do several coats 20 minutes or so apart). Wait for it to thoroughly dry, then go at it feathering it with 400, 800, 1200 grit wet sanding without working through the paint, then buff it and wax it and you are done. If you get through the paint, then just repeat the process. My 2 cents
Cheers,
Jay
-----Original Message-----
From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of Corbin via groups.io
Sent: Wednesday, November 11, 2020 6:18 PM
To: main@Q-List.groups.io Group Moderators <main@q-list.groups.io>
Subject: [Q-List] Slight Damage to Canopy

What’s the recommended fix for this bit of damage to the canopy edge?  I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy.  But it wasn’t there the last time I flew for certain.






Corbin

--
Corbin
N33QR













--
 
Mike Steinsland


Re: Slight Damage to Canopy

Sam Hoskins
 

Something that small and non-structural I would use JB Weld.

Sam 

On Wed, Nov 11, 2020, 9:30 PM One Sky Dog via groups.io <Oneskydog=aol.com@groups.io> wrote:
No bondo over epoxy It will come off.

Charlie


On Nov 11, 2020, at 6:44 PM, Jay Scheevel <jay@...> wrote:

I would just use bondo, then sand it down flush, paint it with some matching white urethane (just use a brush and do several coats 20 minutes or so apart). Wait for it to thoroughly dry, then go at it feathering it with 400, 800, 1200 grit wet sanding without working through the paint, then buff it and wax it and you are done. If you get through the paint, then just repeat the process. My 2 cents
Cheers,
Jay
-----Original Message-----
From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of Corbin via groups.io
Sent: Wednesday, November 11, 2020 6:18 PM
To: main@Q-List.groups.io Group Moderators <main@q-list.groups.io>
Subject: [Q-List] Slight Damage to Canopy

What’s the recommended fix for this bit of damage to the canopy edge?  I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy.  But it wasn’t there the last time I flew for certain.






Corbin

--
Corbin
N33QR












Re: Slight Damage to Canopy

Jay Scheevel
 

Dang, I knew I shouldn't have glued my wings on with that stuff!

Sent from my Verizon Wireless 4G LTE DROID


"One Sky Dog via groups.io" <Oneskydog@...> wrote:

No bondo over epoxy It will come off.

On Nov 11, 2020, at 6:44 PM, Jay Scheevel <jay@...> wrote:

I would just use bondo, then sand it down flush, paint it with some matching white urethane (just use a brush and do several coats 20 minutes or so apart). Wait for it to thoroughly dry, then go at it feathering it with 400, 800, 1200 grit wet sanding without working through the paint, then buff it and wax it and you are done. If you get through the paint, then just repeat the process. My 2 cents
Cheers,
Jay
-----Original Message-----
From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of Corbin via groups.io
Sent: Wednesday, November 11, 2020 6:18 PM
To: main@Q-List.groups.io Group Moderators <main@q-list.groups.io>
Subject: [Q-List] Slight Damage to Canopy

What’s the recommended fix for this bit of damage to the canopy edge?  I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy.  But it wasn’t there the last time I flew for certain.






Corbin

--
Corbin
N33QR












Re: Slight Damage to Canopy

One Sky Dog
 

No bondo over epoxy It will come off.

On Nov 11, 2020, at 6:44 PM, Jay Scheevel <jay@...> wrote:

I would just use bondo, then sand it down flush, paint it with some matching white urethane (just use a brush and do several coats 20 minutes or so apart). Wait for it to thoroughly dry, then go at it feathering it with 400, 800, 1200 grit wet sanding without working through the paint, then buff it and wax it and you are done. If you get through the paint, then just repeat the process. My 2 cents
Cheers,
Jay
-----Original Message-----
From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of Corbin via groups.io
Sent: Wednesday, November 11, 2020 6:18 PM
To: main@Q-List.groups.io Group Moderators <main@q-list.groups.io>
Subject: [Q-List] Slight Damage to Canopy

What’s the recommended fix for this bit of damage to the canopy edge?  I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy.  But it wasn’t there the last time I flew for certain.






Corbin

--
Corbin
N33QR












Re: Slight Damage to Canopy

Jim Patillo
 

I’m with Phil on this one. It’s a leading edge.

Jim
N46JP Q200

Sent from Outer Space


From: main@Q-List.groups.io <main@Q-List.groups.io> on behalf of Phil Lankford via groups.io <britmcman@...>
Sent: Wednesday, November 11, 2020 5:37:19 PM
To: main@q-list.groups.io <main@q-list.groups.io>
Subject: Re: [Q-List] Slight Damage to Canopy
 
Mix up a little cotton flox and epoxy and shape it to your liking. Phil
> On Nov 11, 2020, at 5:18 PM, Corbin via groups.io <c_geiser@...> wrote:
>
> What’s the recommended fix for this bit of damage to the canopy edge?  I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy.  But it wasn’t there the last time I flew for certain.
>
>
>
>
>
>
> Corbin
>
> --
> Corbin
> N33QR
>
>
>
>
>
> <image5.jpeg>
> <image6.jpeg>
> <image7.jpeg>







Re: Slight Damage to Canopy

Jay Scheevel
 

I would just use bondo, then sand it down flush, paint it with some matching white urethane (just use a brush and do several coats 20 minutes or so apart). Wait for it to thoroughly dry, then go at it feathering it with 400, 800, 1200 grit wet sanding without working through the paint, then buff it and wax it and you are done. If you get through the paint, then just repeat the process. My 2 cents
Cheers,
Jay

-----Original Message-----
From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of Corbin via groups.io
Sent: Wednesday, November 11, 2020 6:18 PM
To: main@Q-List.groups.io Group Moderators <main@q-list.groups.io>
Subject: [Q-List] Slight Damage to Canopy

What’s the recommended fix for this bit of damage to the canopy edge? I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy. But it wasn’t there the last time I flew for certain.






Corbin

--
Corbin
N33QR


Re: Slight Damage to Canopy

Phil Lankford
 

Mix up a little cotton flox and epoxy and shape it to your liking. Phil

On Nov 11, 2020, at 5:18 PM, Corbin via groups.io <c_geiser=icloud.com@groups.io> wrote:

What’s the recommended fix for this bit of damage to the canopy edge? I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy. But it wasn’t there the last time I flew for certain.






Corbin

--
Corbin
N33QR





<image5.jpeg>
<image6.jpeg>
<image7.jpeg>


Slight Damage to Canopy

Corbin
 

What’s the recommended fix for this bit of damage to the canopy edge? I’m only assuming my avionics guy left something hanging out of the cockpit and then shut the canopy. But it wasn’t there the last time I flew for certain.






Corbin

--
Corbin
N33QR


Re: Q-2 /Q-200 parts for sale almost free

Mike Steinsland
 

I'm looking for a top and bottom  cowl
How much?
Mike
705-774-3275

On Wed, Nov 11, 2020, 2:15 PM Stan Susman, <stanpfa@...> wrote:
Gang, I have some factory new Q-2 parts for sale. I need them gone fast. If you belong to a EAA chapter of have another 501c3 org I will donate them.
top and bottom fuse.
top and bottom tail cone 
most bulkheads
canopy
top and bottom cowl
I also have some 4A-084 engines (2 new) and prop hubs
e-mail stanpfa@... or call 831-334-3035 near Watsonville ca
thanks


Re: Q-2 /Q-200 parts for sale almost free

Martin Skiby
 

I have a nearly complete plane.  Wings, fuselage with tinted canopy installed, most all the hardware, wings with the wadalow layup.  LS canard, control surfaces etc.  No cowlings.

There is a bunch here and needs to be complete.  e-mail me at mskiby@... and I can send photos.




-----------------------------------------

From: "Anthony P"
To: main@Q-List.groups.io
Cc:
Sent: Wednesday November 11 2020 12:27:12PM
Subject: Re: [Q-List] Q-2 /Q-200 parts for sale almost free

Mr. Martin Skiby, where are your parts located?


Re: Q-2 /Q-200 parts for sale almost free

Martin Skiby
 

Bakersfield, CA

-----------------------------------------

From: "Anthony P"
To: main@Q-List.groups.io
Cc:
Sent: Wednesday November 11 2020 12:27:12PM
Subject: Re: [Q-List] Q-2 /Q-200 parts for sale almost free

Mr. Martin Skiby, where are your parts located?


Re: Q-2 /Q-200 parts for sale almost free

Anthony P
 

Mr. Martin Skiby, where are your parts located?


Re: Q-2 /Q-200 parts for sale almost free

Martin Skiby
 

I have a set of wings and the LS canard has a spar in it.  But I don't want to break up the kit so if he wants they he would need to buy the whole thing.

Then lots of spare parts he would have :)


-----------------------------------------

From: "Bruce Crain"
To: main@Q-List.groups.io
Cc:
Sent: Wednesday November 11 2020 11:20:40AM
Subject: Re: [Q-List] Q-2 /Q-200 parts for sale almost free

Cody Craig needs a carbon fiber spar if you  have one!
Bruce


---------- Original Message ----------
From: "Stan Susman" <stanpfa@...>
To: main@Q-List.groups.io
Subject: [Q-List] Q-2 /Q-200 parts for sale almost free
Date: Wed, 11 Nov 2020 11:14:53 -0800

Gang, I have some factory new Q-2 parts for sale. I need them gone fast. If you belong to a EAA chapter of have another 501c3 org I will donate them.
top and bottom fuse.
top and bottom tail cone 
most bulkheads
canopy
top and bottom cowl
I also have some 4A-084 engines (2 new) and prop hubs
e-mail stanpfa@... or call 831-334-3035 near Watsonville ca
thanks




Q2 misc brake parts

Jerry Marstall <jnmarstall@...>
 

Anyone interested?  Contact me at jnmarstall@... 


Re: Q-2 /Q-200 parts for sale almost free

Jay Scheevel
 

Hi Stan,

 

WE have a non profit group (501c3) called HAWK Aviators, that has kids learning to build airplanes and fly airplanes, here in Mack Colorado (https://hawkaviators.org/). I just forwarded your note to them, so if they are interested, they will contact you pronto.

 

Cheers,

Jay

 

From: main@Q-List.groups.io <main@Q-List.groups.io> On Behalf Of Bruce Crain
Sent: Wednesday, November 11, 2020 12:18 PM
To: main@Q-List.groups.io
Subject: Re: [Q-List] Q-2 /Q-200 parts for sale almost free

 

Cody Craig needs a carbon fiber spar if you  have one!

Bruce

---------- Original Message ----------
From: "Stan Susman" <stanpfa@...>
To: main@Q-List.groups.io
Subject: [Q-List] Q-2 /Q-200 parts for sale almost free
Date: Wed, 11 Nov 2020 11:14:53 -0800

Gang, I have some factory new Q-2 parts for sale. I need them gone fast. If you belong to a EAA chapter of have another 501c3 org I will donate them.
top and bottom fuse.
top and bottom tail cone 
most bulkheads
canopy
top and bottom cowl
I also have some 4A-084 engines (2 new) and prop hubs
e-mail stanpfa@... or call 831-334-3035 near Watsonville ca
thanks

 

2861 - 2880 of 53546