main@Q-List.groups.io

Tailwheel Spring

Has anyone upgraded the tailwheel Spring from fiberglass to steel? Trying to prevent another break (done by previous owner).

By Nick Wright · #55871 ·

Re: Wing foam

The foam that ACS sells is 16"x8" XPS PIB (eXtruded PolyStyrene Pipe Insulation Billet); I don't think the main wing can be done in one piece (the largest piece has an ~18" chord). I spoke to

By James N · #55870 ·

Re: File /Q200_POH_supplement.zip uploaded #file-notice

Here is the related Q-talk article: Q-talk 129 - So What Is Your Gross Weight? -- -MD #2827 (still thinking about planning on visualizing how to finish building)

By Michael Dunning · #55869 ·

Re: File /Q200_POH_supplement.zip uploaded #file-notice

Thanks David! --

By Bill Allen · #55868 ·

File /Q200_POH_supplement.zip uploaded #file-notice

The following files and folders have been uploaded to the Files area of the main@Q-List.groups.io group. /Q200_POH_supplement.zip By: David J. Gall

By Group Notification <noreply@...> · #55867 ·

Re: Wing foam

I have a set of 3 blue foam blocks suitable for Q-200 wings plus a set of carbon fiber spars in El Cajon California. Hmmmm. Should I sell? Phil Lankford

By britmcman99 · #55866 ·

Re: Wing foam

If you are in Southern California, you can drive to Aircraft Spruce in Corona and pick it up. That will save you the shipping and also give you a chance to shop in their showroom. Cheers, Jay

By Jay Scheevel · #55865 ·

Re: Wing foam

ACS is about the only real supplier. Wait till you see the shipping cost. Yikes!

By dflybldr · #55864 ·

Wing foam

Variac ready, wire frame ready, counter balance and overhead pulley ready, table ready. Cutting templates. Blue Docks Billets prices are scary. Have had very good luck in past cutting 2 lb blue

By Ben Wilson · #55863 ·

Re: Experience Spraying Zolatone?

Be sure and post the results 👍 -- -MD #2827 (still thinking about planning on visualizing how to finish building)

By Michael Dunning · #55862 ·

Re: Experience Spraying Zolatone?

After reading all your feedback, I have decided to go with Krylon and a clear coat over it. Thanks!!! -- Robert "TheFrisco" Schmid (408)

By Robert Schmid · #55861 ·

Re: Experience Spraying Zolatone?

Robert, I have a Dragonfly the interior was painted with Zolatone in 1989 by 2011 the paint was looking dingy and basically bad. I went to Home Depot and picked out a high quality latex trim paint. It

By One Sky Dog · #55860 ·

Re: Experience Spraying Zolatone?

I had good results with application described in pages 10-14 in the linked document http://n8wq.scheevel.com/documents/build_logs/11_N8WQ-log_Finishing-Painting.pdf If the only thing you get out of it

By Jay Scheevel · #55859 ·

Re: Experience Spraying Zolatone?

Spray can

By Jim Patillo · #55858 ·

Re: Experience Spraying Zolatone?

What's a "spray bomb"? -- Robert "TheFrisco" Schmid (408) 805-5450 www.facebook.com/TheFlyingFriscos www.theflyingfriscos.com Love building planes almost as much as flying. Latest completed build is

By Robert Schmid · #55857 ·

Re: Experience Spraying Zolatone?

Too many little corners you cant get with a roller If I were using that in my airplane I'd go with the spray bomb Its easier than you think

By Mike Steinsland · #55856 ·

Re: Experience Spraying Zolatone?

I thought I can't roll Zolatone? That would make it at much easier! -- Robert "TheFrisco" Schmid (408) 805-5450 www.facebook.com/TheFlyingFriscos www.theflyingfriscos.com Love building planes almost

By Robert Schmid · #55855 ·

Trunk Spatter Paint | NAPA Auto Parts

https://www.napaonline.com/en/search?text=trunk%20spatter%20paint&referer=v2

By Dave Dugas · #55854 ·

Re: Experience Spraying Zolatone?

If you use Zolatone don’t stir it! Just roll the container over and over until it is mixed. If you stir it you will get colors mixing and streaking. That’s from 26 years ago so I may not be

By Bruce Crain · #55853 ·

Re: Experience Spraying Zolatone?

I'm trying to remember... I think I bought 3 cans of grey spatter paint and used most of it .

By Dave Dugas · #55852 ·

Messages