Hi All, Nothing special to report, but I took a nice flight this morning and fiddled with a lot of things in the cockpit while I enjoyed the vacant skies near here. I landed and emerged from the plane

So I just went to Prince Props to see cost and timing for a new prop ... Turns out their wait time is 10 months, yes TEN MONTHS. I know many of you are using Catto props and I have reached out to them

Hello again, Spring Fling update: I talked to HUF tower this morning. They'll be glad to have us....just shut up and do what your told. :) Naw really....they're pretty flexible. Follows are a few key

I am sitting here and appreciating how active, how helpful and how responsive everyone here is ... I SO APPRECIATE IT. I am new to Quickies, and while its not my first plane I am building, I know I ha

A Good morning, I finally removed the vacuum system from my plane and installed two AV30’s with Wifi Link and OAT probe. See pictures below. I wanted to maintain the Legacy look, yet have AHRS/EFIS ca

Selling my tri q project. Located in Zephyrhills Florida $4000

Hi Guys, Pretty soon I will be getting my Revmaster rebuilt. As far as I know the engine is stock as in the original kit. I'm looking for advise on the minimal upgrades recommended and things to pay a

I have a few leads on a the O-200 exhaust pipes that cross underneath the engine and have one pipe out the cowling. But I read and heard in YouTube videos that with the straight out exhaust and 2 pipl

I like it lost 17 lbs of vacuum junk

I think the answer is in the "Part #" column. https://www.mcmaster.com/steel/shape~round-tube/easy-to-weld-4130-alloy-steel-round-tubes/ -- Q2 N86KL

Anyone has the dimensions of the O-200 engine mount please? Thanks Robert -- Robert "TheFrisco" Schmid (408) 805-5450 www.facebook.com/TheFlyingFriscos www.theflyingfriscos.com Love building planes al

Hi Guys, I recently learned of a Tri-Q that was flying out our Bay Minette AL. Apparently the plane was disassembled and removed from the airport yesterday. Anyone know who that might be? Was hoping t

As part of my research for adding a reflexor to "Duckie", I ran into one picture of an electric reflexor setup by Jon Finley I believe, looked like a Ray Allen servo https://q-list.groups.io/g/main/ph

At the off-chance, any of you have a B&C starter for the O-200 around you'd sell? I believe the one I need/want is the lightweight B&C BC320-1. Someone can hope, right ;-) -- Robert "TheFrisco" Schmid

Looking for 8ft of BID but it's out of stock. Anyone has some left over they are willing to sell or other recommendations where to buy? Thanks Robert -- Robert "TheFrisco" Schmid (408) 805-5450 www.fa

Hi all, I flew my Q200 to Livermore recently to have bob Farnahm ( original builder) help me do my condition inspection. Upon removal of the right elevator we found the midspan hinge was broken. Bob a

I have finally gotten some answers from the motel managers about lodging. I have a block of 15 rooms at the Super 8 in Decorah. 563-382-8771 Her rate: Thursday night $89. Friday and Saturday $149, $20

The rescue project is running full steam, here are some pics of taking off the ailerons, cleaning up the inside and starting on the rudder pedals and elevators. https://www.facebook.com/TheFlyingFrisc

Did another flight last weekend with the camera in a place that is more like the pilots point of view. It has one take off and climb to cruise and then pattern with a landing. Don’t pay much attention

So my aileron connection tube CS11 is bye bye, corroded and needed to be cut into pieces to get the ailerons out. And yes I could just use my calipers and measure it out but I was wondering ... Is the